v8 Miata Forum - Home of the v8 Miata Conversion
A little carbon fiber tape and an exacto knife used to create logo on third brake light
A little carbon fiber tape and an exacto knife used to create logo on third brake light
0 2017/05/03 04:18:20
Third brake light logo
Third brake light logo
0 2017/05/03 04:18:20
Low profile rear spoiler
Low profile rear spoiler
0 2017/05/03 04:15:12
New low profile rear spoiler
New low profile rear spoiler
0 2017/05/03 04:15:12
Gas hood props found on Ebay the original pistons crapped out within a year but found the trunk prop pistons from a 95 Mustang GT worked better
Gas hood props found on Ebay the original pistons crapped out within a year but found the trunk prop pistons from a 95 Mustang GT worked better
0 2017/05/03 04:15:12
Photo03021135
Photo03021135
0 2013/05/09 04:56:18
Photo03091113
Photo03091113
0 2013/05/09 04:54:17
Miata left side after swap original front springs un cut moved to rear nice ride height
Miata left side after swap original front springs un cut moved to rear nice ride height
0 2013/05/09 04:50:34
Miata wheel kosei K1 15X 7
Miata wheel kosei K1 15X 7
0 2013/05/09 04:50:34
miata right side after swap
miata right side after swap
0 2013/05/09 04:50:34
IMG 3950
IMG 3950
0 2013/03/11 04:29:49
IMG 3951
IMG 3951
0 2013/03/11 04:29:49
IMG 3949
IMG 3949
0 2013/03/11 04:29:49
IMG 3863
IMG 3863
0 2013/03/05 04:13:06
IMG 3866
IMG 3866
0 2013/03/05 04:13:06
IMG 3862
IMG 3862
0 2013/03/05 04:13:06
IMG 3841
IMG 3841
0 2013/01/28 09:39:26
IMG 3851
IMG 3851
0 2013/01/28 09:39:26
IMG 3850
IMG 3850
0 2013/01/28 09:37:51
IMG 3837
IMG 3837
0 2013/01/28 09:37:51
Frame mod needed to install 95 SN Mustang GT motor. to allow clearance for AC compressor and power steering pump
Frame mod needed to install 95 SN Mustang GT motor. to allow clearance for AC compressor and power steering pump
0 2013/01/09 10:06:25
New 16 GA cover plate which incorporates sway bar mount
New 16 GA cover plate which incorporates sway bar mount
0 2013/01/09 10:06:25
Fabricated steel filler piece for frame modification
Fabricated steel filler piece for frame modification
0 2013/01/09 10:05:11
IMG 3816
IMG 3816
0 2013/01/09 10:05:11
Front frame modification for stock ford power steering pump clearance
Front frame modification for stock ford power steering pump clearance
0 2013/01/09 10:05:11
Front left suspension installed KYB adjustable shocks
Front left suspension installed KYB adjustable shocks
0 2013/01/03 09:48:09
New rear Hubs,bearings and seals installed
New rear Hubs,bearings and seals installed
0 2013/01/03 09:43:38
Front right suspension installed KYB adjustable shocks
Front right suspension installed KYB adjustable shocks
0 2013/01/03 09:43:38
Firewall cut and painted
Firewall cut and painted
0 2013/01/03 09:43:38
Used aftermarket carrier bushings which required a little modification. The lower bushing was too fat to start the mounting nut so I used a 2-5/8 hole saw to cut a circle in the center 1/4 inch deep and sawzall to cut the outter edge to fit into the new differential carrier
Used aftermarket carrier bushings which required a little modification. The lower bushing was too fat to start the mounting nut so I used a 2-5/8 hole saw to cut a circle in the center 1/4 inch deep and sawzall to cut the outter edge to fit into the new differential carrier
0 2012/12/05 08:57:39
Differential installed 7.5 ring gear 3.27 gear ratio- trac loc
Differential installed 7.5 ring gear 3.27 gear ratio- trac loc
0 2012/12/05 08:57:39
New bushings installed in carrier
New bushings installed in carrier
0 2012/12/05 08:57:39
IMG 3728
IMG 3728
0 2012/11/19 12:08:10
IMG 3727
IMG 3727
0 2012/11/19 12:07:09
IMG 3729
IMG 3729
0 2012/11/19 12:07:09
IMG 3714
IMG 3714
0 2012/11/19 12:07:09
95 Mustang GT motor
95 Mustang GT motor
0 2012/11/19 12:05:17
IMG 3726
IMG 3726
0 2012/11/19 12:05:17
Out with the old
Out with the old
0 2012/11/19 12:05:17